|
|
MULTI-PARAMETER PATIENT MONITOR MODEL : MPPM1001 |
| |
DISPLAY
| Type : |
640 X 480 pixel color TFT |
| Screen Size : |
10.4 inch diagonal |
DISPLAYED PARAMETERS
| Time : |
Battery-backed quartz crystal clock |
| Alarms: |
Hi & lo limits selectable on patient para. |
| ECG : |
ECG Waveform Scale, displayed lead |
| Heart Rate : |
Derived from ECG |
| NIBP : |
Pressure (systolic, mean and diastolic) |
| Pulse Ox.: |
Pulse Rate, Pulse waveform, & % sat |
| RR Apnea : |
Respiration rate derived from ECG. |
| Trends : |
HR, RR, NIBP, Temp.& SpO2 |
| Temperatures : |
One channel (2nd channel optional) |
| Trace Freeze : |
Traces A or B |
ECG
Protected against defib. & electro surgery potentials
| Standard Lead |
I, II, III, AVL, AVR, AVF, V1, V2, V3, V4, 5,V6 |
| Display |
5, 7, 10,15, 20, 25mm/mV |
| Gain Scales |
|
| Sweep Speed |
12mm/s, 25mm/s, 50mm/s |
| Input Resis. |
> 5M Ohm |
| Freq. Response |
0.05Hz-100Hz (3dB) |
| C M R R |
>80dB |
| Electrode Offset |
Maximum ±0.3V |
Potential
Baseline
Recovery |
<5s after 5KV defibrillation |
| Heart Rate range |
15 to 300bpm |
| Resolution |
1bpm |
| Accuracy |
<100bpm ±1% =100bpm ±2% |
| Alarm |
Heart rate hi & lo limits alarm delay<12s |
| Lead Off condition |
Detected and displayed |
Spo2
| Display range |
0 to 100% |
| Accuracy |
80-100%:±2digits; 7 0-69% Unspecified 0-80%:±3digits; |
| Alarm delay |
Spo2 hi & lo limits alarm delay<7s |
| Resolution |
1% |
| Display Update |
<5s |
PULSE RATE
| Measurement Range |
20 to 250bpm |
| Resolution |
1bpm • Accuracy : ±1bpm |
| Alarm delay |
Pulse rate hi & lo limits alarm delay<7s |
RR
| Technique |
Trans-thoracic impedance (RA-LL) |
| Range |
0-100 rpm • Resolution : 1 rpm |
| Accuracy |
±2 rpm (0-60rpm) |
| Alarm delay |
Resp. rate hi & lo limits alarm delay<7s |
TEMP
| Technique |
Resistance |
| Channels |
One channel (2nd channel optional) |
| Scales |
F. Or C. |
| Range |
0-50. • Resolution : 0.1. • Accuracy ±0.1. |
| Alarm delay |
Body temperature hi & lo limits alarm delay<7s |
NIBP
| Technique |
Oscillometric method (with inflatable cuff) |
| Patient Types |
Adult, Pediatric and Neonate |
| Cuff Inflation Time |
3-15 seconds depending on cuff size. |
| Cuff Inflation Pressure |
Initially 180mmHg for Adult/Pediatric (100 or 70 mmHg for Neonate). Subsequent inflation pressures determined by last measured systolic pressure. |
| Measurement Modes |
Manual Immediate upon operator command AUTO Determinations automatically made with selectable intervals. STAT Determinations continues in 5 minutes |
| Measurement Range |
| Adult : |
| Systolic : |
30-255mmHg
|
| Diastolic : |
15-220mmHg
|
| Mean Arterial |
20-235mmHg |
| Infant: |
|
| Systolic : |
25-220mmHg
|
| Diastolic : |
10-150mmHg
|
| Mean Arterial |
15-160mmHg |
|
| Pressure Resolution |
1mmHg |
| Accuracy |
| Cuff Pressure Range: |
0to 275mmHg |
| Pressure Span Accuracy: |
±3mmHg |
| Mean difference: |
±5mmHg |
|
| Standard deviation |
8mmHg |
| Determination Time |
Typically 25seconds. Varies with patient's PR,
pulse pressure and amount of artifact present. |
| Over pressure Valve |
Automatically releases cuff pressure if inflation
Pressure exceeds 280mmHg (Adult) /150mmHg (Neonate). |
| Overtime Protection |
Stop determinates if the measurement time
exceeds 120s (Adult)/90s. (Neonate). |
| Alarm delay |
Pressure hi & lo limits alarm delay<7s |
POWER REQUIREMENTS
| Power Supply |
100~240VAC,50/60Hz 1.6A max |
| Internal Battery |
12V 7AH; Type- sealed lead-acid |
| Operating Time
(fully charged battery) |
2 hours typical at 25.,no printing, one NIBP
measurement per 15 min. |
ENVIROMENT
| Operating Temp: |
5. to 45. |
| Relative Humidity: |
0 to 80%, non-condensing |
| Height of sea level: |
-500m ~ 4600m |
The transport and storage environment should comply with the following conditions:
| Storage Temperature: |
-20. to 70. |
| Relative Humidity: |
0 to 93%, non-condensing |
| Height of sea level: |
-500m ~ 13100m |
OPTIONAL ACCESSORIES
Thermal Printer
IBP modules
SPO2 sensors
NIBP cuffes
2nd Temperature Channel / Probe,
|
|
|
|
